agk

AGK Reference Guide - Airframe & General Knowledge

✈️ AGK Reference Guide

Airframe & General Knowledge - Complete Technical Reference

⚡ Quick Reference - Critical Numbers

3000 psi
Hydraulic Operating Pressure
7-9 psi
Cabin Differential Pressure
400 Hz
AC Frequency
10,000 ft
Cabin Altitude Warning
-5 to +18°C
Carb Icing Conditions
15,000 ft
O₂ Mask Auto-Deploy

Core System Design, Load, Stress & Maintenance

Damage/Fault Tolerant Design

  • Capability to withstand weakening without catastrophic failure
  • Takes cracking into account
  • Structure can degrade gradually

Fail Safe Design

  • Multiple load-carrying components
  • Parallel structural parts with load sharing
  • Based on redundancy
  • ⚠️ Does NOT imply system will never fail

Safe Life Design

  • Replacement after given cycles/flight hours
  • One load-carrying component sufficient if strong enough
  • ⚠️ Does NOT imply system won't fail during safe life period

⚠️ Important Note

There is NO most favorable design method - each component varies based on requirements and criticality.

1. Hard Time Maintenance

Component overhauled/removed after a set number of hours/cycles regardless of condition.

  • Scheduled replacement
  • Independent of actual component state
  • Predictable maintenance planning

2. On Condition Maintenance

Monitoring critical parameters and replacement if limit value exceeded.

  • Condition-based replacement
  • Continuous monitoring required
  • More efficient resource use
Stress = Force / Area

1. Tension

Force resisting being pulled apart

2. Compression

Push force - opposite of tension

3. Shear

Force parallel to cross section

4. Torsion

Caused by twisting

5. Torque

Axial rotation force

6. Buckling

Effect of more than one force

Strain

Deformation due to stress, expressed as a % change of dimension of original dimension.

Elastic Deformation

  • Tendency of material to return to original state
  • Temporary - reverses when load removed
  • Material operates within elastic limit

Permanent Deformation

  • Occurs when aircraft flies beyond certified load factor
  • Material exceeds elastic limit
  • Cannot return to original shape

Corrosion (Incorrect Metallic Bonding)

1. Stress Corrosion

Continuous tensile load + corrosion environment

2. Intergranular Corrosion

Attacks grain boundaries inside metal

⚠️ Fatigue

Material is continually loaded & unloaded and will eventually break even though load magnitude remains the same.

  • Caused by cyclic loading
  • No visible warning before failure
  • Critical for high-cycle components
Classification No Effect Minor Major Hazardous Catastrophic
Qualitative None Probable Remote Extremely Remote Extremely Improbable
Quantitative None 10⁻³ 10⁻⁵ 10⁻⁷ 10⁻⁹
Flight Crew None Slight workload Physical discomfort Physical distress Fatality/Incapacitation
Airplane Margins None Slight reduction Significant reduction Large reduction Hull loss
Passengers Inconvenience Physical discomfort Physical distress Serious/fatal injury Multiple fatalities

Structure Airframe Construction

Engine Compartment

Decking & firewall constructed from stainless steel or titanium sheet

Sandwich Structure

  • Two thin sheets separated with light core material
  • Low mass, high stiffness
  • Stabilizes covering sheets
  • ⚠️ Unsuitable for concentrated loads
  • Does NOT use resin

Composite Structure

  • Consists of matrix & fibers
  • Strength tailored to direction of load
  • NOT same strength in all directions
  • Higher strength-to-weight ratio vs metals

Truss Type

  • Used in small light aircraft
  • Training planes
  • Simple tubular framework

Monocoque

  • Takes all load on stressed skin
  • Uses aluminum/magnesium alloy
  • No internal framework

Semi-Monocoque

  • Fuselage of transport airplanes
  • Consists of: skin, frames & stringers
  • Uses aluminum/magnesium alloy
  • Most common modern design

Fuselage Components

  • Skin: Outer covering that bears aerodynamic loads
  • Frames: Maintain fuselage cross-sectional shape
  • Stringers: Run longitudinally, support skin
  • ⚠️ NO spars or girders in fuselage (wings only)

Cantilever Wing

  • Attached to aircraft at wing root ONLY
  • No struts, braces, or wires
  • Vertical loads & bending moments highest at wing root

Torsion Box

Main structural element consisting of: spars, ribs, wing skin reinforced by stringers

Ribs

Function: Maintain aerodynamic shape

  • Run chordwise (front to back)
  • Support wing skin
  • Transfer loads to spars

Stringers

Function: Assist skin to absorb longitudinal compressive loads

  • Run spanwise (root to tip)
  • Prevent skin buckling
  • Share compression loads

Wing Skin

  • When unable to bear load, transfers to spar via ribs & stringers
  • Bears cylindrical load during pressurization (TENSION)
  • Aerodynamic surface

Spar

  • Bears MOST of the load
  • Consists of web & girders (I-beam)
  • Main structural member
  • Runs spanwise

In the Air

  • Lift loads carried by upper/lower skin surfaces & spars
  • TENSION on lower surface
  • COMPRESSION on upper surface
  • Wing bends upward

On the Ground

  • TENSION on upper surface
  • COMPRESSION on lower surface
  • Wing sags under own weight
  • Opposite of flight loads

Wing Bending Moments - Reduction Methods

  • Installing "upfloat" ailerons
  • Using fuselage fuel first while maintaining fuel in wings as long as possible
  • This reduces inertia relief during flight

Wing Torsion

  • Effect of aileron deflection
  • Effect of positive sweep (surfaces hit air at non-uniform levels)
  • From wing root to tip: First compression, then tension

⚠️ Flutter Mechanism

Caused by torsion & bending when COP ahead of COG

Prevention Methods

  • Increase torsional stiffness
  • Add balancing mass in front of control surface hinge
  • Ensure correct mass distribution within control surface during design

Wing Bends Downward

Flutter may occur if aileron deflects UPWARDS (aileron COG behind hinge line)

Wing Bends Upward

Flutter may occur if aileron deflects DOWNWARDS (aileron COG behind hinge line)

T-Tail Configuration

Vertical stabilizer is NOT affected by wing turbulence influence

  • Horizontal stabilizer mounted on top of vertical fin
  • Cleaner airflow to elevator
  • Better deep stall characteristics

Pressurization Load

Fuselage pressurization creates TENSION loads in the skin

Shell Structures Transmit

  • Normal bending
  • Tangent bending
  • Tension
  • Torsional stresses
  • ⚠️ NO SHEAR

Torque Links

Most stress occurs when making tight turns during taxiing, turning at a small radius

Floor Proximity Emergency Escape Lights

Provides additional guidance during evacuation in reduced visibility

Window Heating System

  • De-icing provided by electrical heating
  • Some aircraft have speed restrictions related to bird impact when heating inoperative
  • Window heating improves strength of cockpit windows
  • Used on continual basis to reduce thermal gradients

Construction & Systems

  • Made of: Glass
  • Inner surface: Soft polycarbonate laminate
  • Supplied by 3-phase AC
  • Heating systems cycle ON/OFF to maintain temperature between 18°-35°C

Cockpit Side Windows

NOT provided with de-icing, only defoggers

Indications

  • Green system "On" information light
  • Amber failure warning light

⚠️ Long Haul vs Short Haul

Airplanes designed for long haul CANNOT be used for short haul flights

Reason: Lifetime of fatigue-sensitive parts has been determined on a specific load spectrum

  • Short haul = more takeoff/landing cycles
  • Different fatigue accumulation rates
  • Component life based on design mission profile

MZFM - Maximum Zero Fuel Mass

Total maximum permissible mass of the aircraft WITHOUT usable fuel

  • Limits wing bending relief from fuel weight
  • Protects wing structure
  • Important for payload planning

Systems Hydraulic Systems

Pascal's Law

Pressure exerted on hydraulic fluid within an enclosed system - the pressure will increase equally throughout the fluid and act at right angles to container walls

Pressure = Force / Area
Area(A) × Distance(A) = Area(B) × Distance(B)

Operating Pressure

Most common operating pressure: 3000 psi

Hydraulic Power

Hydraulic power is a function of system pressure & volume flow

Power = Pressure × Flow Rate

Maximum Power Output & Low Mass

Achieved by having high pressure system & low volume flow

Most Common Types

  • Phosphate ester based fluids (Skydrol)
    • Color: PURPLE
    • Most widely used
  • Synthetic oil (maybe mineral)
    • Synthetic = Highest resistance against cavitation

Required Properties

  • Thermal stability
  • Low emulsifying characteristic
  • Anti-corrosive
  • High flash point
  • Irritating to eyes & skin ⚠️
  • Incompressible
  • Ideally low viscosity to minimize power consumption

Monitoring Parameters

  • Pressure
  • Fluid temperature
  • Quantity

Pressure Indicator

Transducer connected to an indirect indicator

⚠️ Internal Leaks

Will cause fluid temperature increase

Reason: Pistons/accumulators work harder → becomes hotter

Open Centre Circuit

Has capabilities for idle flow

  • Fluid continuously circulates
  • System always pressurized
  • Simpler design

Hydraulic Braking System

Uses nitrogen as gas medium

Shuttle Valves

Switches between 2 sources of pressure

  • Switch hydraulically operated units to most appropriate pressure supply
  • Enables alternate supply to an actuator

Selector Valve

Direct system pressure to either side of piston of an actuator

Check/Non-Return Valve

Works like an electronic diode - allows fluid to flow in one direction only

Pressure Relief Valves

Protects against excessive system pressure

Cut-Out Valve

Used in a fixed volume pressure control hydraulic system

High Pressure Relief Valve

Failure of normal method of system pressure limiting control

Relief Valve

Makes sure pressure does NOT exceed permitted pressure in the system

Actuator/Jack Function

Converts hydraulic pressure into linear motion

Hydraulic Lock

Occurs when no movement of piston takes place

Single Actuator

Powered in one direction only by hydraulic power

Return movement by another force (spring, gravity)

Variable Displacement vs Constant Pump

Variable pump adjusts fluid pumped to fluid required

Moves fluid only when necessary

Separate Pressure Regulator

Used with constant delivery type pump

Hand Pumps

Connected to bottom of reservoir

Axial Piston Pumps

  • Produces high pressure when required
  • Can be off-loaded to reduce power consumption

Pump Failure

Quill drive will shear to offload & protect gearbox

Over Heat Detectors

Installed at the pumps

Low Pressure Alert

Located at pump outlet

Indicates insufficient pump output

Filter Location

In both pressure & return lines

Pop-Out Indicators

Warn of impending clogging/by-pass

  • Visual indication of filter condition
  • Indicates when maintenance needed

When Powering Up

Fluid in reservoir will decrease slightly

Fluid Level Fluctuation

Discounting leaks, it fluctuates with:

  • Jack displacement
  • Accumulator pressure

Pressurization

Pressurized using bleed air to:

  • Prevent cavitation in pump inlet to EDP
  • Ensure inlet provided with continuous supply of fluid free from foaming

Temperature Measurement

Hydraulic fluid temperature measured here

Functions

  • Store fluid under pressure (energy storage)
  • Provide limited alternate supply in emergency
  • Dampen out fluid pressure fluctuations/variations
  • Allow for thermal expansion
  • Cater for small internal leaks

⚠️ Internal Leak Detection

Hydraulic fluid found in gas container = Internal leak in accumulator

The Security of Hydraulic System Comprises:

  • Filters
  • Pressure Relief Valves
  • By-pass valves
  • Fire Shut-off valves
  • Hydraulic fuse: Prevent total system loss in event of leak/rupture
  • Quill drive: Shear to offload & protect gearbox
  • Ram Air Turbine (RAT): Flight controls in event of loss of engine-driven hydraulic power
  • Stack pipe: In hydraulic reservoir to provide emergency supply

Systems Landing Gear Systems

Compressed Nitrogen Bottle

Used in emergency to lower landing gear & keep doors opened

Auxiliary Hydraulics

Backup hydraulic system

Free-Fall/Gravity

Method when there is complete hydraulic failure

Damping Element

Hydraulic fluid/oil

  • Provides damping action
  • Absorbs landing energy

Spring Element

Nitrogen

  • Provides spring action
  • Compressible gas

VLO

Speed at which landing gear can be operated with full safety

VLE

Flight speed with landing gear down

Amber Light

At least one wheel is in traveling/unlocked condition

Green Light

Landing gear is locked down

Over-Centre Mechanism Principle

Down lock mechanism uses over-centre principle

Locks landing gear in the up/down position

Torsion Links/Scissors

Avoids rotation of piston rod relative to gear oleo strut

⚠️ Retracting on Ground Prevented By:

  • Electrical control system routed through weight on wheels switch
  • Anti-retract latch (can be overridden under specific conditions)
  • Latch located in landing gear lever
  • Locking pins with flags

Shimmy

  • Damaging vibration of nose wheel while on ground
  • Tendency of sinusoidal motion on ground
  • Overcome by using accumulator associated with steering cylinder

Steering

Achieved by mechanical rods connected to rudder pedals

Components

  • Speed sensor
  • Control unit/computer
    • Inputs: Idle & braked wheel speed, desired idle wheel train slipping rate
  • Control valve

Operation

  • Available when using auto-brakes
  • Activates when main wheel spin-up detected
  • Brake pressure decreased on slower spinning wheels

Parking Brake System

Fitted together with its own accumulator & system components

Disconnection

  • By pressing pedals
  • By pilot action after landing

Characteristics

  • Low level: Works without delay
  • Works during thrust reversal
  • Works above pre-set minimum speed

Accumulator Function

Supplies limited amount of brake energy in event of hydraulic system loss

Brake Units for Transport Category Aircraft

Multiple disks

Brake Life Extension

Extended by:

  • Using steel brakes
  • Use many small brake applications during taxi
  • Preventing temperature buildup

Hydroplaning

Occurs when friction coefficient = 0

Operation

  • Activates maximum braking with anti-skid above a certain speed
  • Activates as soon as take-off rejected & throttles moved to idle
  • Is armed at low speeds

Under-Inflated Tires

More wear at the shoulders

Tubeless Tire Advantages

  • Lower risk of bursting
  • Better adjustment to wheels
  • Requires solid/branched wheels
  • Eliminates internal friction between tube & tire
  • No built-in air tube
  • A radial side casing

Tire-Creep

  • Circumferential movement of tire in relation to wheel flange
  • Tire marks align with rim marks
  • A normal problem

Ply Rating

Parameter indicating tire relative strength

Overheat Protection

Due to prolonged braking:

  • Hollow bolt screwed into wheel rim
  • Melts at given temperature (thermal fuse)
  • Deflates tire to prevent exploding/bursting

Maintenance

Worn tires can be repaired several times

Controls Flight Control Systems

Primary Controls Include:

  • Ailerons
  • Elevators
  • Rudders
  • Roll spoilers

Elevators

Control: Lateral axis

Motion: Pitch

Ailerons

Control: Longitudinal axis

Motion: Roll

Rudder

Control: Normal/Yaw/Vertical axis

Motion: Yaw

Yoke Rearward & to the Left

  • Right aileron moves DOWN
  • Left aileron moves UP
  • Elevator moves UP

Yoke Forward & to the Right

  • Right aileron moves UP
  • Left aileron moves DOWN
  • Elevator moves DOWN

Manual Flight Control

Cable-reversible

  • Direct controls using cables (e.g., Cessna 172)

Power Assisted Control

Hydraulic-reversible

  • Direct controls with hydraulic help

Powered Controls

Irreversible

  • Use hydraulic pressure & servo motors

Power Assisted Controls

Do NOT require Q-feel system

Powered Controls

REQUIRE Q-feel system (artificial feel)

Pitch Trim

Achieved by moving the tab

Roll Trim & Yaw Trim

Achieved by moving the controls (yoke or pedals)

= Moving neutral point/zero force point of Q-feel

Characteristics

  • Requires gust lock
  • There IS feedback to pilot's controls of aerodynamic forces
  • Are less complex
  • Does NOT require artificial feel

Characteristics

  • Does NOT require gust lock
  • When one hydraulic system lost: Remaining systems take over
  • Requires artificial feel unit
  • There is NO feedback to pilot's controls of aerodynamic forces
  • Trimming achieved by adjusting "zero force point" of feel system

Function

Prevent movement of control column if controls NOT fitted with servo tabs

When gust lock ON: Provisions to prevent take-off

Rudder Limiters

Restrict rudder deflection during high IAS

Rudder Ratio Changer

Reduces rudder deflection for given rudder pedal deflection

As IAS increases (NOT decrease)

Variable Stop System

Limits both rudder & rudder pedal deflection

As IAS increases

Rudder Trim

  • Actuation on ground with engine running: Rudder moves, pedals move in corresponding direction
  • An adjustment of zero force rudder position
  • In fully powered (irreversible) systems: By altering neutral position of artificial feel unit

Function & Connection

  • Connected in parallel with primary controls
  • Functions in parallel with irreversible hydraulic actuator
  • Fitted to prevent over-stressing of aircraft
  • Provides increased forces as speed increases

Control Surface Range of Movement

Restricted/limited by primary stops at the surface

Control Jamming Protection

Disconnect part of control system that becomes blocked

Control Column/Wheel

  • Zero force position does NOT change when using pitch
  • Zero force position CHANGES when using aileron trim

Over-Tensioned Cables

Results in excessive friction in cables

Hydraulic Valves

Acts on actuator of control surface

V-Tail Aircraft

Controls that act together: Stick in one axis & rudder pedals

Large Aircraft Without Trim Tabs

Trimming possible by adjusting neutral point of artificial feel mechanism via trim switch

Secondary Controls Include:

  • Speed-brakes
  • Lift augmentation devices
  • Trimmable stabilizer (moved by hydraulically actuated jacks)

Trim Tabs

Reduce hinge moments but reduce control surface efficiency

Auto Slat System

Extends slats automatically when certain angle of attack reached

Receives signal from stall warning system

Elevator Trim

Double switch used to reduce possibility of trim runaway

(When trim system malfunctions)

Spoilers

  • Located symmetrically on wing surface
  • Ground spoiler extension activated when main wheel spin-ups

Fowler Flaps (Trailing Edge)

Moves aft then turns down

Krueger Flaps (Leading Edge)

Located close to root

Most Basic Mode

Direct

System Description

Based on electrical (analogue) signals from computer sent to hydraulic actuators

Modes

  • Normal
  • Alternate
  • Direct
  • Mechanical

Advantages

  • Direct & indirect weight savings through simplification of systems
  • Improvement of piloting quality throughout flight envelope

Systems Pneumatic & Air Conditioning Systems

Primary Uses

  • Used for cabin pressurization
  • Usually taken from low pressure stage/low pressure bleed air valve of high stage compressor
  • High pressure stage from high pressure compressor if necessary

⚠️ Important Note

Engine's bleed air is NOT considered high pressure

It only takes air from high pressure compressor

Piston Engine Aircraft

Uses ram air or inlet air manifold

Differential Pressure

7-9 psi

Why Pressurization Required

At altitudes above 10,000 ft there is sufficient ambient air pressure to force oxygen into lungs to allow normal breathing

Flight Level/Ambient Pressure = Cabin Altitude Pressure - Differential Pressure

Positive Pressure

Cabin pressure higher than ambient

Negative Pressure

Cabin pressure lower than ambient

Negative pressure relief valves open

Cabin Altitude Decreasing

  • Pressure inside cabin increasing
  • Cabin rate of climb decreasing

⚠️ Important Fact

Percentage of oxygen remains constant regardless of cabin air compression or pressurization

Limitation of Pressurized Cabin

Due to maximum positive cabin pressure at maximum cabin altitude

Functions

  • Control cabin altitude
  • Control rate of change
  • Limit differential pressure

Control Method

By delivering substantially constant flow of air into cabin & controlling outflow

Maintain cabin altitude via position of outflow valves

How Cabin Pressure Regulated

Cabin pressure regulated by airflow leaving cabin

Outflow valves remain partially open in level flight

Ditching Controls

Close outflow valves when landing on water

Flight Altitude & Differential Pressure Constant

Mass air flow through cabin is constant

During Climb/Descent

Cabin pressure decreases more slowly than atmospheric pressure

Mode 1: Constant Pressure Differential

Changing differential pressure slowly during climb/descents

Mode 2: Isobaric

Maintains same cabin pressure during climbs/descents

⚠️ Excessive Cabin Altitude Warning

Activates at 10,000 ft

Cabin Altitude Rate of Change Selector

Controls cabin altitude rate of change

Sequence of Events

  • Cabin altitude & cabin vertical speed increases until differential is zero
  • Then cabin VSI shows descent equal to aircraft VSI

Differential Pressure Rise

Differential pressure will rise to maximum value

Causing safety relief valves to open

In Level Flight - Outflow Valves Locked

Cabin pressure will rise

Indicating descent on cabin altitude indicator

Pressure Relief Valve

Acts in case pressure reducing valve malfunctions

Definition

Air that has been controlled in respect to temperature & pressure

Automatic Control Failure

Pilot can revert to manual control & set valve to required setting

Pack Cooling Fans

Supplies heat exchanger with cooling air during slow flight & ground operations

Pack Inlet Inflow Valve

Used to maintain constant & sufficient air mass flow to ventilate cabin

Cycle Sequence

(1) Air supply/first heat exchanger → (2) Compressor → (3) Heat exchanger (second) → (4) Expansion turbine COOLING

Water separation comes after expansion turbine stage

Mnemonic: ACHE

Purpose

Refers to cold air unit/air cycle machine arrangement

Mainly for turboprop

Primary function: Cool bleed air

Air Cycle Machine/Air Conditioning Pack

Causes pressure & temperature drop in bleed air

Mass Air Flow Routing

Routed to secondary heat exchanger outlet to turbine inlet

Turbine Function

  • Drives compressor
  • Creates temperature drop in conditioned air

Compressor Function

  • Increases temperature of air
  • Makes heat exchanger more efficient

Expansion Turbine

Reduces air temperature & pressure

Heat Exchangers

Cools bleed air in front & behind compressor of air cycle machine

Primary Heat Exchanger

Precools engine bleed air

Secondary Heat Exchanger

Cools air behind pack's compressor

⚠️ Important Safety Feature

Is separate to prevent exhaust gas from contaminating cabin air

Prevents CO poisoning in MEPs

Fuel Source

Powered by fuel from aircraft fuel system

Short-Haul Turbojet Aircraft

Cabin air humidity is NOT controlled

Protection Ice Protection Systems

⚠️ Critical Components Requiring Ice Protection

  • Engine air intake & pod
  • Front glass shield
  • Pitot tubes (always provided with heater)
  • Static tubes (may also be heated)
  • Waste water masts
  • Leading edges of wings (slats partially/completely)
  • A part of or whole leading edge

Most Common for Large Jets

Bleed air from HP compressor

Over-Temperature Warning

Indicated by warning lights

Effect on Thrust

Reduces max thrust

Aerodynamic Performance

Does NOT affect aerodynamic performance

Anti-Icing Protection

  • Engine inlets
  • Pitot & static ports

De-Icing Protection

  • Wings

Propeller Protection

Protected electrically

Application

  • For wings
  • Used for large turboprop
  • Used for de-icing ONLY

Operation

Operated when approximately 1.5 cm of ice on leading edges visibly

Inflates each pneumatic boot for few seconds

Method

Uses slinger rings

Application

On small surfaces

  • Used for pitot-tubes
  • Used for static ports
  • Used for windshield

Heating System Characteristics

  • Electric heating
  • Heating facility used on continual basis
  • Reduces thermal gradients which adversely affect useful life
  • Supplied by 3-phase AC
  • Heating systems cycle ON/OFF to maintain temperature between 18°-35°C

Hot Rod Ice Detector

  • Accumulate ice & visible from cockpit
  • A heated probe & built-in floodlight

Rotor Ice Detector

Measurement based on torque

Pressure Differential/Smith's Ice Accretion Detector

  • Small holes freeze first
  • Activated by decrease in dynamic pressure

Rosemount Vibrating Ice Detector

  • Light in cockpit alerts crew of aircraft icing
  • Principle of vibration

Advisory System

Flight crew activates based on standard flight manual criteria

Total temperature reading & sighting of moisture

Ice detector signals serve as back-up indicator

Automatic System

Ice detector automatically activates ice protection systems at optimal moment

Primary Manual System

Flight crew activates based on ice detector signals

Systems Fuel & Fuel Systems

Flash Point

  • Lowest temperature of vapor at which it ignites in contact with flame
  • Vapor ignites in contact with flame & extinguishes immediately

AVGAS - Aviation Gasoline (Piston Engines)

  • AVGAS 100: GREEN
  • AVGAS 100LL: BLUE
  • AVGAS 80: RED

MOGAS

Increased risk of carburetor icing

Type Jet A Jet A-1 Jet B
Freezing Point -40°C -47°C -60°C
Flash Point 38°C 38°C -20°C
Density at 15°C (kg/l) 0.78-0.83 0.78-0.83 0.75-0.8

Transport Aircraft Wing Tanks

Integral - built internally into aircraft structure

  • Saves weight & space
  • Most common for large aircraft

Small Aircraft

  • Fuel stored in wings
  • Incorporates volumetric top-off valve float switches
  • Typically measured by level of fuel tank (NOT volume)

Usable Fuel

Total amount of fuel that can be supplied to engine

Unusable Fuel

Sometimes minimized by incorporation of tank sump pads

Moisture Accumulation Prevention

By keeping tanks full when not in use

Ice Traps

Fitted in fuel delivery line between fuel tank & engine

Water in Fuel Detection

Presence of water indicated by fluid forming at bottom of strainer

Reason: Water is heavier than fuel

Fuel Additives

Added to fuel to prevent ice crystals from forming/waxing

Fuel Pressure Measurement

Measured in line between booster pump & engine

OR at outlet of high pressure filter

Solenoid Valve

Electrically operated/activated

Cross Feed Valve

  • Ensure all fuel on board available to any engine
  • Adjust fuel distribution

Fuel Control Unit

Protected from debris by fine filter located between HP fuel pump & governor unit

Fuel Heaters

  • Located at the engine
  • Prevent risk of ice formation from water contained in fuel at low temperatures

LP Booster Pumps

  • Avoid vapor locking
  • Prevent cavitation/bubble accumulation of HP fuel pump
  • Electrically driven centrifugal pumps
  • 20-100 psi
  • Direct feed lines to engine at positive pressure

HP Booster Pump

Driven by engine

DC Fuel Pump

Can only feed the APU

Ventilation

Prevents low pressure or excessive overpressure in tank

  • Pressure kept ambient
  • 2% of total tank space in each individual tank vent space

Baffles

Restrict fuel movement in tank during maneuvers/sideslip

Pressure Refueling

  • Automatic fueling shut-off valve switches off fuel supply system when fuel reached predetermined value or mass
  • Magnetic drip stick: Measurement done with indicator & documentation
  • Stops fueling as soon as certain fuel level reached inside tank

⚠️ Safety Protocol

Bonding & connections to earth terminal between ground equipment & aircraft should be made BEFORE filler cap removed

Refueling Point

Via a unique point: Underwing refueling centre

When Required

On aircraft where MTOW is higher than MLW

Purpose

Fuel dumping to a predetermined safe value

Purpose

  • Minimizes wing G-loads
  • Preserve main tanks for landing

Systems Electrical Systems

P = V × I
R = V / I
  • Power: Watt
  • Work/Energy: Joules
  • Most common frequency: 400 Hz

⚠️ Temperature Effect

Resistance increases with increasing temperature

Open Circuit

Loss of continuity prevents components from functioning

Mnemonic: CIVIL

  • In Capacitor: Current leads Voltage
  • In Inductance: Voltage leads Current

Capacitive Reactance

  • Reactance ↑ → Frequency ↓ → Current ↓

Inductive Reactance

  • Reactance ↑ → Frequency ↑ → Current ↓

General Characteristics

  • Used in both AC & DC
  • May be reset manually after fault rectified

Trip Free

Doesn't allow contacts to be held until fault rectified

Magnetic

Quick tripping response

Thermal

Protects against:

  • Overload/overheating
  • Prolonged overcurrent

Primary Functions

  • Provides safe distribution of electrical charge/currents (MAIN)
  • Protect against lightning
  • Reduce radio interference
  • Ensure 0 voltage difference between aircraft components
  • Set aircraft to a single potential
  • Provide single earth for electrical devices

Functions

  • Wicks safely dissipate static charge of aircraft in flight
  • Placed on wing & tail tips to facilitate electrical discharge
  • Reduce interference with on-board radio communications to minimum
  • Limits risks of transfer of electrical charges between aircraft & electrified clouds

Diode/Semiconductor

Allows electrical flow in one direction only

Zener Diode

Used for voltage stabilization

Light Duty/Cartridge

Ceramic with thin wire

Current Limiter

Allow short term overload before rupturing

Heavy Duty/HRC

Used in high current circuits

Main Function

Be an emergency source of electric power

Capacity

Measured in Ampere-hours

⚠️ Thermal Runaway

Significant increase in battery temperature

Lead Acid Battery

  • 1 cell output approx. 2-2.2V
  • Any cell breaks: Whole battery unserviceable
  • Tested by comparing "on-load" & "off-load" voltages

NiCad (Nickel-Cadmium)

  • Reduced charging time
  • Constant output voltage
  • Even voltage before rapid discharge
  • Weighs less than lead-acid
  • Good discharging-charging capability
  • Wider temperature range
  • Good storage capabilities
  • Sturdy metal casing
  • Potassium hydroxide electrolyte

NiCad Monitoring

  • Need monitoring from excessive temperature caused by decreasing voltage
  • High risk of thermal runaway

Parallel Batteries

Same voltage, sum of capacity

Series Batteries

Sum of voltages, same capacity

Battery Discharge Indicator

When battery almost fully discharged: Tendency for voltage to decrease under load

Battery Check

Load should be applied to give better indication of condition

High Charge Rate

Normal at start-up

However NOT normal when it persists

Battery Control Unit Isolates Battery:

  • From bus when charging complete
  • When battery overheats
  • In case of internal short circuit

Conversion

  • AC → DC: TRU/Rectifier
  • DC → AC: Inverter

Brushless AC

Activated by set of permanent magnets

AC Supply Charges Battery

Via Transformer Rectifier Units (TRU)

Generator Output Control

Controlled by varying field strength

AC Alternators

Have fixed induced windings (Stator)

Dynamos

Have fixed inductor (Field) coil & moving rotor

Alternator Rotor Coils

DC

Alternator Stator Coils

AC

Frequency of Current

Depends on rotation speed

Frequency "Wild"

Output frequency varies with engine speed

Feeder Fault on DC Circuit

Results in flux unbalance between voltage coil & series winding turn

RPM = (Frequency × 2 × 60) ÷ Number of Poles

Functions

  • Drives generator at constant speed
  • Ensures electric generator maintains constant frequency
  • Can be disconnected from drive shaft
  • Is hydromechanical
  • Can be disconnected in flight

Voltage Regulation

Requires voltage controller/regulator to maintain constant voltage under variable load

⚠️ Reset Limitation

Can only be reset on ground after engine shut down

During Fault

CSD should be disconnected provided engine still running

Red Arc Indication

Should be disconnected

Generator unusable for rest of flight

Monitoring

  • Oil temperature
  • Low oil pressure

Functions

  • Controls current
  • Controls output voltage at varying loads & speeds
  • Controls power required for field excitation of main rotor
  • Increases excitation current when load increases
  • Connected in series with shunt field coil

Series Wound

  • Voltage varies with load
  • High starting load

Shunt Wound

  • Voltage decreases slightly with load increase
  • Needs presence of magnetic field & min rotation speed

Compound Wound

  • Voltage constant

Star-Connected

  • Line voltage: √3 × Phase voltage
  • Line current: Phase current

Delta-Connected

  • Line voltage: Phase voltage
  • Line current: √3 × Phase current

Starter Warning Lights

Illuminates when starter motor clutch engaged

Generator Control Unit (GCU)

Modern GCUs provided with permanent indication to record failure

All commands from control panel applied via GCU EXCEPT dog clutch release

DC Advantages

  • Simple connection
  • High starting torque
  • DC generators connected in parallel to provide maximum power

AC Advantages

  • Flexibility in use
  • Light weight components
  • Easy to convert to DC
  • Easy maintenance

HOT BUSSES & DC BUSSES

Directly connected to battery

Bus Bar

A distribution means for electrical power

Bus Tie-Breaker (BTB)

  • Allows power to be applied to failed AC generator's bus bar
  • Ties generator to other bus bars & components
  • Opens when there is phase imbalance between generator & other main busbars/generators

Generator Control Breaker (GCB)

Connects generator to busbar

Generator Control Relay/Exciter Breaker (GCR)

Switches excitation of generator field on/off

  • Closes when generator voltage greater
  • Opens when battery voltage greater

Over/Under Excitation

Exciter breaker & generator breaker OPEN

Underspeed

Only generator breaker OPENS

Generator Relay

Ensures voltages are almost equal before generators paralleled

Reverse Current Relay

Ensures battery does NOT supply current to generator

When battery voltage exceeds generator voltage

When Loads Are Switched Off

  • Current reduces

During Isolation

AC busbar current consumption decreases

Load Sharing Requirements

Both real & reactive loads must be matched

  • Real load: Regulated by torque from CSD/equalizing circuit (Drive shaft controls frequency) kVA
  • Shared/reactive load: Regulated by voltage regulator (Excitation current controls voltage) kVAR

Paralleled Generators (Connected to Same Busbar)

Requirements:

  • Equal voltage
  • Equal frequency
  • Equal phase rotation
  • Voltage of same phase
  • Current unimportant

Unparalleled Generators

Phase unimportant

Load Shedding

Temporary/permanent switching off of certain electric users

Purpose: Avoid overload of generators

Protected From:

  • Over-voltage
  • Under-voltage
  • Over-current
  • Over-speed
  • Under-frequency

Grounding Negative Pole

Of aircraft structure making it return path to earth

Advantages:

  • Single pole circuit
  • Weight saving
  • Easy fault detection
  • Reduction of short circuit risk

DC Starter Motors

Series wound

Reverse Direction of Rotation

By reversing polarity of stator OR rotor

📚 Complete AGK Reference Guide

This comprehensive guide covers all major AGK topics including Piston Engines, Turbine Engines, Fire Protection Systems, and Oxygen Systems.

Use the search function above to quickly find specific topics, or navigate through sections using the menu.

Study Tip: Focus on highlighted numbers, critical warnings (red boxes), and quick reference cards for exam preparation.